Product ID:SUPER ALLOY TITANIUM PUTTY RESIN
MSDS Date:06/01/1988
FSC:8030
NIIN:00N022049
Kit Part:Y
MSDS Number: BLNYW

ITW PHILADELPHIA RESINS CORP

130 COMMERCE DR
MONTGOMERYVILLE, PA 18936
US

Emergency Phone: 215-855-8450

Info Phone: 215-855-8450

Cage: ITWPH

ITW PHILADELPHIA RESINS

454 MONTGOMERYVILLE, PA 18936 US

Telephone: 508-777-1100

Cage: ITWPH

DGBA EPOXY RESINS; (EPOXY RESIN, DIGLYCIDYL ETHER OF

CAS: 25068-38-6

RTECS: SL6475000

SILICA GEL

CAS: 112945-52-5

RTECS: VV7310000

TALC (CONTAINING NO ASBESTOS)

CAS: 14807-96-6

RTECS: WW2710000

OSHA PEL 2 MG/M3 RDUST

ACGIH TLV: 2 MG/M3 RDUST; 9192

LD50 LC50 Mixture:LD50:(ORAL RAT) 11.4 G/KG
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:SKIN:RESIN IS MOD IRRIT & MAY CAUSE
SENSIT. EYE:MOD IRRIT. CORNEAL DAM IS UNLIKELY. INHAL:BECAUSE OF
ITS VERY LOW VOLATILITY, THIS PROD IS NOT LIKELY TO PRDCE ANY
ADVERSE EFTS BY INHAL. THE INHAL HAZ OF THE FILLERS, INGRED 2 & 3,
SHOULD NOT APPLY UNLESS THE CURED PROD IS GROUND OR MACHINED TO
(SEE EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ:PRDCE A DUST. INGEST:RESIN IS
GENERALLY CONSIDERED TO HAVE A LOW ORDER OF ACUTE ORAL TOX.
SIGNS/SYMPS: IRRITATION AS NOTED. SKIN SENSITIZATION (ALLERGY) MAY
BE EVIDENCED BY RASHES, ESPECIALLY HIVES.
Medical Cond Aggravated by Exposure:PRE-EXISTING SKIN ALLERGIES MAY
INCREASE THE CHANCE OF DEVELOPING INCRD ALLERGY SYMPS FROM EXPOSURE
TO THIS PRODUCT. PREEXISTING SKIN & EYE DISORDERS MAY BE AGGRAVATED
BY EXPOSURE TO THIS PRODUCT.

First Aid:EYE:IMMED FLUSH W/PLENTY OF WATER FOR AT LEAST 15 MINS WHILE
HOLDING EYELIDS OPEN. GET MD. SKIN:IMMED REMOVE CONTAMD CLTHG. WIPE
EXCESS FROM SKIN & FLUSH W/PLENTY OF WATER FOR AT LEAST 15 MINS.
USE SO AP IF AVAIL OR FOLLOW BY WASHING W/SOAP& WATER. IF EFTS
PERSIST, GET MD. DO NOT REUSE CLTHG UNTIL THORO CLEANED. LEATHER
ARTICLES INCL SHOES CANNOT BE DECONTAMD & SHOULD BE DESTROYED. (SEE
SUPP DATA

Flash Point Method:TOC
Flash Point:>400F,>204C
Extinguishing Media:CARBON DIOXIDE, DRY CHEMICAL & POLYMER FOAM FOR
LARGE FIRES.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
PROTECTIVE EQUIPMENT . AVOID BREATHING SMOKE.
Unusual Fire/Explosion Hazard:NONE KNOWN.

Spill Release Procedures:AVOID PERSONAL CONT. SCRAPE UP AS MUCH
MATERIAL AS POSSIBLE & PLACE IN A SUITABLE, LABELED, CONTAINER FOR
WASTE DISPOSAL. RESIDUE MAY BE REMOVED USING A SAFETY SOLVENT. IF
SOLVENT IS USED FOR CLEANING , TAKE PRECAUTIONS AGAINST FIRE &
PERSONAL EXPOS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:STORE IN A COOL, DRY PLACE W/ADEQ
VENT. KEEP AWAY FROM OPEN FLAME & HIGH TEMP. HANDLE I/A/W THE
HAZARD POTENTIAL OF CURING AGENT.
Other Precautions:PRACTICE GOOD HOUSEKEEPING PROCEDURES TO AVOID ALL
SKIN CONTACT & BREATHING OF VAPORS.

Respiratory Protection:NOT ORDINARILY REQD FOR RESIN. NIOSH/MSHA APPRVD
RESP PROT SHOULD BE SUITABLE FOR ALL WORKING CNDTNS ON THE JOB.
DUST MASKS SHOULD BE WORN DURING ANY GRINDING/MACHINING PROCEDURES
ON CURED RESINS. ORG RESPS MAY BE REQD IN CONFINED SPACES.
Ventilation:GENERAL:GOOD GENERAL VENTILATION IS USUALLY ADEQUATE FOR
MOST INDUSTRIAL APPLICATIONS.
Protective Gloves:IMPERVIOUS RUBBER OR PLASTIC GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:WEAR CLEAN LONG LEG & SLEEVED CLOTHING.
Work Hygienic Practices:WASH THOROUGHLY AFTER HANDLING & BEFORE
SMOKING, EATING OR USING TOILET FACILITIES.
Supplemental Safety and Health
MATLS TO AVOID:RELSD WHEN REACTED W/ UNCONTROLLED AMTS OF CURING AGENT.
FIRST AID PROC:REMOVE VICTIM TO FRESH AIR & PROVIDE O2 IF BREATHING
IS DIFFICULT. GET MD. INGEST:DO NOT INDUCE VOMITING. IF CONS CIOUS,
GIVE TWO GLASSES OF WATER & IMMEDIATELY SEEK A MD'S ATTN. NEVER
GIVE ANYTHING BY MOUTH TO AN UNCON PERSON.

HCC:N1
Vapor Pres:NIL @ 78F
Spec Gravity:1.7
Solubility in Water:NEGLIGIBLE
Appearance and Odor:VISCOUS GRAY PASTE; LOW ODOR.
Percent Volatiles by Volume:0

Stability Indicator/Materials to Avoid:YES
CAN REACT VIGOROUSLY W/STRONG OXIDIZING AGENTS & STRONG LEWIS/MINERAL
ACIDS. CONSIDERABLE HEAT CAN BE (SEE SUPP DATA)
Stability Condition to Avoid:STABLE UNDER MOST INDUSTRIAL CONDITIONS.
Hazardous Decomposition Products:AS W/ANY OTHER ORG MATL, COMBUST WILL
PRDCE CARBON DIOXIDE & PROBABLY CARBON MONOXIDE AS WELL AS
ALDEHYDES & ACIDS.

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE W/FEDERAL, STATE &
LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.